甚本性能参数如下:
1.) The performance parameters are as follows:
1.生产线总装机容量:450KW
1.Total installed capacity of production line: 450KW
2.实际耗电量:220~280KW/小时
2.Actual power consumption: 220 ~ 280KW / hour
3.机械线速度:4-20m/min
3.Mechanical linear speed: 4-20m / min
4.成品幅宽:1600mm
4.Width of finished product: 1600mm
5.产品克重:8~120g/m2
5.Product weight: 8 ~ 120g / m2
6.熔喷纤维:2~5μm
6. Meltblown fiber: 2 ~ 5μm
7.均匀度CV值:s4%
7.CV of uniformity: ≤4%
8.卷最大直径:600mm
8.Roll maximum diameter: 600mm
9.最大年产量:丝径:2~5μm时330年。
9. Maximum annual output: wire diameter: 330 years at 2 ~ 5μm.
10机器占地面积约L15000mm*5000mm*H5000mm,
10 The machine covers an area of about 15000mm * 5000mm * H5000mm,
11.机器重量:约13吨(以实物重量为准)
11.Machine weight: about 13 tons (based on actual weight)
12.(电压:三相电380V50Hz)
(1) 12. (Voltage: three-phase power 380V50Hz)
2.)生产线操作工人人数：
生产分二班每班3人:辅助工1人,技术人员2人
1.) Number of workers operating the production line:
Production is divided into two shifts of 3 people each: 1 auxiliary worker, 2 technical staff
3.)设备配置如下:
3.) Equipment configuration is as follows:
3.1主机料斗一个(材质:不锈钢、带料位视窗及插板,)
真空自动上料机一台，控制功率:3KW
3.1 host hopper (material: stainless steel, window with material level and insert plate,)
A vacuum automatic feeding machine, control power: 3KW
3.2挤出机: φ90押出主机一套(φ90机筒和螺杆主机平台)
90mm机筒1套
3.2 Extruder: φ90 extruder set (φ90 barrel and screw host platform)
1 set of 90mm barrel
材料:38 CrMoLALA(优质氮化钢)
Material: 38 CrMoLALA (high quality nitrided steel)
氮化硬度:740HV
Nitriding hardness: 740HV
氮化层深度:0.5-0.8mm
Nitrided layer depth: 0.5-0.8mm
螺杆直径:φ90mm
Screw diameter: φ90mm
螺杆长径比:30:1
Screw aspect ratio: 30: 1
螺杆形式:专用螺杆(适合於PP溶喷专用)
Screw form: special screw (suitable for PP solution spraying)
材料:38rMo(优质氮化钢)
Material: 38rMo (high quality nitrided steel)
氮化硬度:740HV
Nitriding hardness: 740HV
主机减速箱一套
1 Set of host gearbox
主机电机功率:45KW
Host motor power: 45KW
控制形式:交流变频控制
Control form: AC variable frequency control
主机加热区:5区
Host heating zone: zone 5
每区加热功率:6.0KW(铸铜加热器)
Heating power per zone: 6.0KW (cast copper heater)
总加热功率:32.5KW
Total heating power: 32.5KW
冷却方式:风冷
Cooling method: air cooling
风冷区:5区
Air-cooled zone: Zone 5
每区风冷功率:180W
Air cooling power per zone: 180W
4.)主机单流道双孔位液压快换网一套(板式)
4.) One set of single-channel dual-position hydraulic quick-change screen for the host (plate type)
控制方式:液压控制
Control method: hydraulic control
控制功率:2.2KW
Control power: 2.2KW
液压缸径:φ100mm
Hydraulic cylinder bore: φ100mm
